UsageSikaEmaco® N 907 can be used as a:
|
Advantages
|
Product Details
Composition
Blend of portland cement, selected aggregates and liquid acrylic
Shelf life
12 months from production date
Storage conditions
Store in a cool, dry area in original sealed packaging and at temperatures between +5°C and +35°C. Protect from direct sunlight, heat and moisture.
Maximum grain size
~0.6 mm
Compressive strength
|
~20 N/mm² (28 d) |
(BS EN 12190) |
Tensile adhesion strength
|
≥ 0.8 N/mm² (28 d) |
(BS EN 1542: 1999) |
Application
Mixing ratio
Part A : Part B – packaging size: 16.66 : 5 kg
Mixing ratio: 3.33 : 1 (by weight)
Layer thickness
Maximum 10 mm
Setting time
|
Working time: |
Temperature: |
|
~30 min |
25°C |
Fresh mortar density
~1.63 kg/l (25°C)
Consumption
As a guide:
~1.6 kg/m2/mm
This figure is theoretical and does not include for any additional material required due to surface porosity, surface profile, variations in level or wastage, etc.
Yield
~13.3 liters per 21.66 kg set
SURFACE PREPARATION
Substrates must be properly cured, structurally sound, free of any loose or friable particles, clean, dry and free of any contaminants such as dust, dirt, oil, grease, cement laitance or efflorescence. Depending on the substrate condition, contaminants should be removed from the surface. Perform adequate preparation techniques, such as water-jet washing or blastcleaning, in order to remove all traces of any materials that could reduce the product’s adhesion to the substrate. For applications in hot climates / environments and / or on absorbent substrates, thoroughly pre-dampen the surface immediately prior to the product application, but avoid any ponding / standing water on the surface, which must not be damp to touch and not with a dark-matt / wet surface appearance i.e. it must be saturated surface dry (SSD).
MIXING
SikaEmaco® N 907 is formulated to produce an easily mixed mortar. A slow speed drill and paddle can be used or a forced action mixer. Add powder to liquid at a steady rate. Mix for approx 4 minutes. Do not add water.
APPLICATION
SikaEmaco® N 907 is applied by steel trowel. The finishing should be carried out with the minimum trowelling. A small amount of water can be applied to the surface to aid finishing. Leave the applied material for a short time before proceeding with final smoothing.
CURING TREATMENT
Curing is generally not required, however during hot, dry and windy conditions the surfaces should be covered to prevent rapid drying. Alternatively, the applied material can be cured with Sika® Antisol® range of curing compounds. This product is compatible with most subsequent coatings.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with water immediately after use. Hardened / cured material can
only be mechanically removed.
There is £4.99 charge for delivery under £50 Orders. Additional charges will be imposed by our couriers for delivery to remote area, a surcharge may be levied to cover carriage to these areas.
SikaEmaco N 907 (Formerly known as MasterEmaco N 907)
43,00 د.إ
Two component polymer modified fairing coat and re-profiling mortar
SikaEmaco® N 907 is a two-component acrylic polymer modified blow hole filler and reprofiling mortar for cement based substrates. Suitable for use in hot and tropical climatic conditions.
- Easy to use
- Excellent workability
- Pre-gauged liquid, no mixing with water
UsageSikaEmaco® N 907 can be used as a:
|
Advantages
|
Product Details
Composition
Blend of portland cement, selected aggregates and liquid acrylic
Shelf life
12 months from production date
Storage conditions
Store in a cool, dry area in original sealed packaging and at temperatures between +5°C and +35°C. Protect from direct sunlight, heat and moisture.
Maximum grain size
~0.6 mm
Compressive strength
|
~20 N/mm² (28 d) |
(BS EN 12190) |
Tensile adhesion strength
|
≥ 0.8 N/mm² (28 d) |
(BS EN 1542: 1999) |
Application
Mixing ratio
Part A : Part B – packaging size: 16.66 : 5 kg
Mixing ratio: 3.33 : 1 (by weight)
Layer thickness
Maximum 10 mm
Setting time
|
Working time: |
Temperature: |
|
~30 min |
25°C |
Fresh mortar density
~1.63 kg/l (25°C)
Consumption
As a guide:
~1.6 kg/m2/mm
This figure is theoretical and does not include for any additional material required due to surface porosity, surface profile, variations in level or wastage, etc.
Yield
~13.3 liters per 21.66 kg set
SURFACE PREPARATION
Substrates must be properly cured, structurally sound, free of any loose or friable particles, clean, dry and free of any contaminants such as dust, dirt, oil, grease, cement laitance or efflorescence. Depending on the substrate condition, contaminants should be removed from the surface. Perform adequate preparation techniques, such as water-jet washing or blastcleaning, in order to remove all traces of any materials that could reduce the product’s adhesion to the substrate. For applications in hot climates / environments and / or on absorbent substrates, thoroughly pre-dampen the surface immediately prior to the product application, but avoid any ponding / standing water on the surface, which must not be damp to touch and not with a dark-matt / wet surface appearance i.e. it must be saturated surface dry (SSD).
MIXING
SikaEmaco® N 907 is formulated to produce an easily mixed mortar. A slow speed drill and paddle can be used or a forced action mixer. Add powder to liquid at a steady rate. Mix for approx 4 minutes. Do not add water.
APPLICATION
SikaEmaco® N 907 is applied by steel trowel. The finishing should be carried out with the minimum trowelling. A small amount of water can be applied to the surface to aid finishing. Leave the applied material for a short time before proceeding with final smoothing.
CURING TREATMENT
Curing is generally not required, however during hot, dry and windy conditions the surfaces should be covered to prevent rapid drying. Alternatively, the applied material can be cured with Sika® Antisol® range of curing compounds. This product is compatible with most subsequent coatings.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with water immediately after use. Hardened / cured material can
only be mechanically removed.
There is £4.99 charge for delivery under £50 Orders. Additional charges will be imposed by our couriers for delivery to remote area, a surcharge may be levied to cover carriage to these areas.
Reviews
There are no reviews yet.
- Free shipping on all orders above 50,00
- No hassle returns, 30 days return
- Next day delivery within your country
Feel free to Get in touch
Related products
SikaEmaco N 907 (Formerly know...
43,00 د.إ
Reviews
There are no reviews yet.